22 gauge Mil Spec Teflon (PTFE) insulated Wire is provided for all the connections from the board to the tube sockets (and from the control pots to the board) and from the input jacks to the board. 

To determine which color to use where, the following arrangement is recommended:

Use the brightest "hot" color in your kit for all the anode (plate) connections. 

For the 12AX7 type preamp tubes, the plates are located at pin 1 and pin 6. Count the tube socket pins as they face you on the tube socket - with the male end up - in a clockwise direction beginning the count at the gap btw pin 1 and pin 9. 

For the 6V6 style tube, use the hot color for the high voltage screen grid of that tube at pin 4. 

Use a cooler color wire for the input grids. 

INput grids are located at pin 2 and 7 on the 12AX7 type tubes. 

And at pin 5 on the 6v6 type tubes. Notice on the 5E3 that there is a resistor across pin 5 and 6. IN this case, the wire connects to pin 6 and the signal is carried from the 220K resistors on the board across that 1.5K resistor on those pins.  

Use your remaining color wire for the cathodes (Kathode). These are located on pin 3 and 8 on the 12ax7 type tubes and at pin 8 on the 6v6 type tubes. 

By using three different colors on the three main functioning components of the vacuum tubes, you will have clarity if the need for troubleshooting your project should arise.   

Green is for the heaters - aka filaments.

Black is for grounds 

      


 Bill of Materials Boot Hill Amps 5F6A Chassis Kit

        1       5F6A Chassis       
        1       Turret Board
  1 PC-CUT Power cord, cut end
  
  1 Wire 5F6A Teflon Coated wire, 5F6A
  (8.5 ft. Red, Orange, Yellow, Green, 1.5 ft. Black, White)
  6 CHK-11 Knob, chicken head, flat top
  1 CF-3 Fuse, 3 amp
  
  3 SKT8 Tube socket, octal
  3 SKT9 Tube socket, 9 pin
    20 Bolt-SKT Bolt, machine, #4-40x3/8, with nut and star washer or captive nut
    
  4 RJP-2 Jack, RCA, chassis mount,
  4 RP-C Plug, RCA, cable mount
  1 FH-2 Fuseholder
   1 PL-2 Pilot light
  1 6N-4 Strain relief
  2 WSW-SPST-3 Carling Switch, toggle, panel mount, SPST
  4 PJP-S Chassis mount phone jack, shorting
  2 Small Grommet 9/16" OD  Chassis Grommets
  1 WP502L Potentiometer, 5K linear
  1 WP253L Potentiometer, 25K linear
  1 WP254L Potentiometer, 250K linear
  3 WP105A-MF Potentiometer, 1 meg audio
  1 Wire Nut Wire Nut, small
  3 #6 machine metal screws with nuts Turret Board Mounting Screws
  
  1 1N4007 Diode rectifier
  1 SMC470-500 Capacitor, 47pF, 500 volts
  1 SMC101-500 Capacitor, 100pF, 500 volts
  1 SMC251-500 Capacitor, 250pF, 500 volts
  1 EC257-25 Capacitor, 250uF, 25 or 50 volts
  2 EC805-150 Capacitor, 8uF, 150 volts
  1 EC805-450 Capacitor, 8uF or 10uF, 450 volts
  4 EC206-500 Capacitor, 20uF or 22uF, 450 volts
  5 PEC223-630 Capacitor, .022uF, 630 volts
  1 PEC473-630 Capacitor, .047uF, 630 volts
  4 PEC104-630 Capacitor, .1uF, 630 volts
  1 MFR470-.5 Resistor, 470, 1/2 watt
  2 MFR820-.5 Resistor, 820, 1/2 watt
  1 MFR10K-.5 Resistor, 10K, 1/2 watt
  1 MFR15K-.5 Resistor, 15K, 1/2 watt
  3 MFR56K-.5 Resistor, 56K, 1/2 watt
  4 MFR68K-.5 Resistor, 68K, 1/2 watt
  1 MFR82K-.5 Resistor, 82K, 1/2 watt
  5 MFR100K-.5 Resistor, 100K, 1/2 watt
  2 MFR220K-.5 Resistor, 220K, 1/2 watt
  2 MFR270K-.5 Resistor, 270K, 1/2 watt
  4 MFR1M-.5 Resistor, 1M ohm, 1/2 watt
  2 MFR470-1 Resistor, 470, 1 watt
  1 MFR4.7K-2 Resistor, 4.7K, 2 watt
  1 MFR10K-2 Resistor, 10K, 2 watt
  
 If parts are missing or damaged, contact Daytona Dave; haircuttingcowboy@yahoo.com 

Output Transformer Shown is not included in Base Model Chassis Kit. Please inquire about availability of components not included in Base Model Chassis Kits.

Boot Hill Amp Chassis Kit: 5F1 Champ  
Bill of Materials  
  
  
  
 Qty
  
 
  1 5F1KT 5F1 Chassis, ground bus wire, fiberglass board
 
  1 PC-CUT Power cord, cut end
  
  1 CCW-5F1 Kit, Teflon-Coated Military-Grade 1000v wire, 5F1
  ( 6 ft. Red, Yellow, Orange, Green, 1ft. Black, White cloth speaker wire)
  1 CHK-11 Knob, chicken head, flat top
  1 CF-2 Fuse, 2 amp
  
  2 SKT8 Tube socket, octal
  1 SKT9 Tube socket, 9 pin
  
  6 Bolt-SKT screws, machine, #4-40x3/8, with k lock nuts
  2                       #6 machine screws with k lock nuts
  
  1 RJP-2 RCA jack, chassis mount, diamond fiber base
  1 RP-C RCA plug, male, cable mount
  1 FH-2 Fuseholder
 
  1 PL-2 Pilot light
  1 6N-4 Strain relief
  2 PJP-S Chassis mount phone jack, shorting
  2 Small Grommet 9/16" OD  Chassis Grommets
 1       WP105AS Potentiometer, 1 meg audio with switch
  1 Wire Nut Wire Nut, small
 
  
  2 EC256-25 Capacitor, 25uF, 25 volts
  2 EC805-450 Capacitor, 8uF, 450 volts
  1 EC166-450 Capacitor, 16uF, 450 volts
  2 PEC223-630 Capacitor, .022uF, 630 volts
  2 MFR1500-.5 Resistor, 1.5K, 1/2 watt
  1 MFR22K-.5 Resistor, 22K, 1/2 watt
  2 MFR68K-.5 Resistor, 68K, 1/2 watt
  2 MFR100K-.5 Resistor, 100K, 1/2 watt
  1 MFR220K-.5 Resistor, 220K, 1/2 watt
  1 MFR1M-.5 Resistor, 1M ohm, 1/2 watt
  1 MFR10K-2 Resistor, 10K, 2 watt
  1 MFR22K-2 Resistor, 22K, 2 watt
  1 RES470-5 Resistor, 470 ohms, 5 watt
  

                                                  5E3 Kit Components

1 Power Cord, Cut End
1 Strain Relief 5/8 inch
1 Wire Kit
(5ft Red, yellow, orange,  7ft Green, 1 ft Black, White for speaker wire)
3 Chicken Head Knobs with Set Screws
3 1M Potentiometers
1 2 Amp Fuse
1 Fuseholder
3 Ceramic Octal Tube Sockets
2 Preamp Tube Sockets Outside Mount 9 Pin with Shields
Bolt Kit for Tube sockets:
Includes 10 machine Screws with k lock nuts
1 Terminal Strip for grounding Preamp side
1 Ground Wire Buss 1 ft.
2 #6 Machine Screws to fasten board to chassis
1 Male 1/4 inch Phone Plug, Speaker Cable Mount
1 Pilot Light
2 Carling SPST Toggle Switches for Power and Standby
1 Female Chassis Mount Phone Jack for Auxillary Speaker
5 Switchcraft Shorting Jacks for 4 inputs and 1 primary Speaker Out
1 Fibreglass turret board
1 Wire nut
1 terminal strip for all grounds on PTx side

Capacitors:
1 Ceramic Tone Capacitor, 500pF, 500v
3 25uF, 25v Cathode Bypass Capacitors, Sprague Vishay
1 22uF, 450v Power Filter Capacitor
2 16uF or greater, 450v "
1 Capacitor .0047uF, 630v Mallory Tone Control
5 PE .025uF or .022uF , 630v coupling capacitors
I use these in all five positions in place of the typical .1uf blocking caps


Resistors
1 Vishay or better 270ohm 5 watt Cathode Bias Resistor
1 820, 1/2 watt
4 1.5K, 1/2 watt
2 56K, 1/2 watt
4 68K, 1/2 watt
3 100k, 1/2 watt
2 220k, 1/2 watt
3 1M ohm, 1/2 watt
1 4.7k, 2 watt
1 22K 2 Watt